Article
  • Investigation on Wear Behavior of PETG and PLA Parts Fabricated with Fused Deposition Modelling Under Different Wear Conditions
  • Gökmen Atlıhan

  • Department of Mechanical and Manufacturing, Pamukkale University, 20400, Turkey

  • 용융 적층 모델링 방법으로 가공된 PETG와 PLA의 마모 거동 연구
  • Reproduction, stored in a retrieval system, or transmitted in any form of any part of this publication is permitted only by written permission from the Polymer Society of Korea.

References
  • 1. Momber, A. W.; Irmer, M.; Marquardt, T. Effects of Polymer Hardness on the Abrasive Wear Resistance of Thick Organic Offshore Coatings. Prog. Org. Coat. 2020, 146, 105720.
  •  
  • 2. Momber, A. W. Quantitative Performance Assessment of Corrosion Protection Sys-tems for Offshore Wind Power Transmission Platforms. Renew. Energy 2016, 94, 314-327.
  •  
  • 3. Momber, A. W.; Marquardt, T. Protective Coatings for Offshore Wind Energy Devices (OWEAs): a Review, J. Coat. Technol. Res. 2018, 15, 13-40.
  •  
  • 4. Lauer, R. S. Advancements in the Abrasion Resistance of Internal Plastic Coatings. Abu Dhabi, UAE, Mater. Perform 2015, 53, 52-55.
  •  
  • 5. Hosseinpour, D.; Guthrie, J. T.; Berg, J. C. The Effect of α-alumina Filler/acrylic-melamine Polymer Interfacial Interactions on the Abrasion Resistance of An Automotive Topcoat Layer; Elsevier: Prog. Organ. Coat. 2008, 62, 214-218.
  •  
  • 6. Zsidai, L.; Katai, L. Abrasive Wear and Abrasion Testing of PA6 and PEEK Composites in Small-scale Model System. Acta Polytech. Hung. 2016, 13, 197-214.
  •  
  • 7. Benli, M.; Gümüş, B. E.; Kahraman, Y.; Gökçen-Rohlig, B.; Evlioğlu, G.; Huck, O.; Özcan, M. Surface Roughness and Wear Behavior of Occlusal Splint Materials Made of Contemporary and High-performance Polymers. Odontology 2020, 108, 240-250.
  •  
  • 8. Zgalat-Lozynskyy, O. B.; Matviichuk, O. O.; Tolochyn, O. I.; Ievdokymova, O. V.; Zgalat-Lozynska, N. O.; Zakiev, V. I. Polymer Materials Reinforced with Silicon Nitride Particles for 3D Printing. Powder Metall. Met. Ceram. 2021, 59, 515-527.
  •  
  • 9. Franco, M. F.; Gadioli, R.; Paoli, M. A. Presence of Iron in Polymers Extruded with Corrosive Contaminants or Abrasive Fillers. Polimeros-Ciencia e Tecnologia 2019, 29, 2.
  •  
  • 10. Yavuz, G. A.; Gören Kıral, B.; Katre, S.; Atilla, D. Effects of Topology and Material on Mechanical Properties of Structures Produced by the Additive Manufacturing Method. Dokuz Eylul University Faculty of Engineering Science and Engineering Journal. 2021, 23, 755-765.
  •  
  • 11. Abeykoon, C.; Sri-Amphorn, P.; Fernando, A. Optimization of Fused Deposition Modeling Parameters for Improved PLA and ABS 3D Printed Structures. Int. J. Lightweight Mater. Manuf. 2020, 3, 284-297.
  •  
  • 12. Ergene, B.; Yalçın, B. Investigation on Mechanical Performances of Various Cellular Structures Produced with Fused Deposition Modeling (FDM). J. Fac. Eng. Archit. Gazi Univ. 2023, 38, 201-217.
  •  
  • 13. Rajesh, J.; Bijwe, J.; Tewari, U. S. Abrasive Wear Performance of Various Polyamides. Wear 2002, 252, 769-776.
  •  
  • 14. Rajesh, J.; Bijwe, J.; Tewari, U. S. Influence of Fillers on Abrasive Wear of Short Glass Fibre Reinforced Polyamide Composites. J. Mater. Sci. 2001, 36, 351-356.
  •  
  • 15. Kumara, S.; Panneerselvam, K. Two-Body Abrasive Wear Behavior of Nylon 6 and Glass Fiber Reinforced (GFR) Nylon 6 Composite. Procedia Technol. 2016, 25, 1129-1136.
  •  
  • 16. Patnaik, A.; Satapathy, A.; Chand, N.; Barkoulad, N. M.; Biswasb, S. Solid Particle Erosion Wear Characteristics of Fiber and Particulate Filled Polymer Composites: A Review. Wear 2010, 268, 249-263.
  •  
  • 17. Harsha, A. P. An Investigation on Low Stress Abrasive Wear Characteristics of High Performance Engineering Thermoplastic Polymers. Wear 2011, 271, 942-951.
  •  
  • 18. Tervoort, T. A.; Visjager, J.; Smith, P. On Abrasive Wear of Polyethylene. Macromolecules 2002, 35, 8467-8471.
  •  
  • 19. Guptaa, M. K.; Srivastava, R. K.; Bisaria, H. Potential of Jute Fibre Reinforced Polymer Composites: A Review. Int. J. Fiber Text. Res. 2015, 5, 30-38.
  •  
  • 20. Mahapatra, L.; Mohanty, S. The Effect of Strain Rate on Jute Fibre Composites; National Institute of Technology: Rourkela, 2007.
  •  
  • Polymer(Korea) 폴리머
  • Frequency : Bimonthly(odd)
    ISSN 0379-153X(Print)
    ISSN 2234-8077(Online)
    Abbr. Polym. Korea
  • 2023 Impact Factor : 0.4
  • Indexed in SCIE

This Article

  • 2023; 47(3): 257-263

    Published online May 25, 2023

  • 10.7317/pk.2023.47.3.257
  • Received on Apr 27, 2022
  • Revised on Feb 16, 2023
  • Accepted on Mar 14, 2023

Correspondence to

  • Gökmen Atlıhan†
  • Department of Mechanical and Manufacturing, Pamukkale University, 20400, Turkey

  • E-mail: gatlihan@pau.edu.tr